| |
FAQ |
|
| |
|
|
| |
Industrial Equipment Division |
|
| |
Typical Questions & Answers |
|
| |
|
|
| |
Q. Does the motor a
constant speed ? |
|
| |
Ans.
Yes, 1440 rpm |
|
| |
|
|
| |
Q. Is it
Possible to supply machine with single phase motor? |
|
| |
Ans.
Yes, at extra cost. |
|
| |
|
|
|
Q. It there any
protection to the motor? |
|
| |
Ans.
Yes, DOL starter is fitted for the same. It prevents even
single phasing. Care should be taken to set current in the relay
as per requirement. |
|
| |
|
|
| |
Q. Is RPM of
motor constant or it can be varied ? |
|
|
Ans.
RPM of motor is constant
|
|
| |
|
|
| |
Q. What make of
motor is used ? |
|
| |
Ans.
Motor from manufacturer having CE mark. |
|
| |
|
|
| |
Q. Is the force
mechanical or pneumatic ? |
|
| |
Ans.
Force is pneumatic using compressed
air. |
|
| |
|
|
| |
Q. Do we need a
compressor to run the machine ? |
|
| |
Ans.
Yes |
|
| |
|
|
| |
Q. What size of
compressor is required ? |
|
| |
Ans.
Depends on the sizes of the machine &
no. of Strokes / Minute. (Ref. Air consumption chart. ) As a
thumb Rule 005 - 1 HP Compressor, 008 -2 HP Compressor, 012- 3
HP Compressor. |
|
| |
|
|
| |
Q. Is compressor
supplied with machine? |
|
| |
Ans.
No, but can be supplied at extra cost. |
|
| |
|
|
| |
Q. What make of
pneumatic cylinder is used ? |
|
| |
Ans.
Pneumatic cylinder is manufactured by us. |
|
| |
|
|
| |
Q. Are the
components liable to be corroded ? |
|
| |
Ans.
The critical parts that come in contact with air are hard chrome
plated. |
|
| |
|
|
| |
Q. Can any
standard make cylinder be fitted on the machine? |
|
| |
Ans.
No, because provision for rotation for
spinning action while riveting, is inbuilt in the cylinder which
is not possible with any standard make. |
|
| |
|
|
| |
Q. What make of
pneumatic is fitted on the machine? |
|
| |
Ans.
Local reputed supplier from Bombay. If required any other make
can be fitted at extra cost. |
|
| |
|
|
| |
Q. Is the PCB
inside the control panel made in house? |
|
| |
Ans.
Yes |
|
| |
|
|
| |
Q. What about
repair? |
|
| |
Ans.
Replacement sent to customer in case
of complaint. No repairing of PCB card possible at customer's
end. Suggest customer to keep a spare PCB Card. |
|
| |
|
|
| |
Q. Is
availability of bearings handy? |
|
| |
Ans.
Yes, even otherwise we stock the
requisite bearings. |
|
| |
|
|
| |
Q. What about
'O' rings & cup seals. Are they available in the market or need
to be purchased from manufacture? |
|
| |
Ans.
These are proprietary items of manufacturer and need to be
procured from us only. |
|
| |
|
|
| |
Q. How often
these need to be replaced? |
|
| |
Ans.
If lubricator in FRL Unit works
satisfactory these may need to be replaced once in 3-4 years of
running of the machine |
|
| |
|
|
| |
Q. How often the
oil needs to be replaced? |
|
| |
Ans.
The lubricator should be set such that
a drop of oil goes for every 10-12 strokes of the machine.
Refilling of oil required once a week. However water in air
collected in the filter should be drained regularly.
|
|
| |
|
|
| |
Q. What is the
availability of connectors & braided hose pipe used : Are they
non-standard? |
|
| |
Ans.
These are standard items available in
any local market. |
|
| |
|
|
| |
Q. What is the
weight of the machine? |
|
| |
Ans.
Net Weight - 005-70 Kg, 008-150 kg, & 012-300 Kg |
|
| |
|
|
| |
Q. Can the
machine be used as a press? |
|
| |
Ans.
Yes, but we do not recommend |
|
| |
|
|
| |
Q. Is the tool
angle changeable? |
|
| |
Ans.
No, it is fixed. However tool with different angle (say 3 Deg. )
can be made available |
|
| |
|
|
| |
Q. Why does the
tool have and angle? |
|
| |
Ans.
Refer technical details in the manual. |
|
| |
|
|
| |
Q. What is the
material of the tool? |
|
| |
Ans.
Material of the tool normally used is WPS (HC HCr). However
tools out of HSS material, hot die steel and carbide tips can be
made on request. |
|
| |
|
|
| |
Q. Can we
regrind the tools if worn out ? |
|
| |
Ans.
No, because tool length is very
critical and contributes towards neat riveting in a big way. |
|
| |
|
|
| |
Q. What is the
life of the tool? |
|
| |
Ans.
If the UTS of material riveted is 38 Kg/ mm x mm about 1,00000 (One Lakh)
Operations. |
|
| |
|
|
